Binatone Speakeasy 600 Manuel d'utilisateur télécharger pdf

Duet 600 – Edition 4.2 – 13.9.00

To adjust the ringer tone and volume

The Duet 600 has 3 ringer tones to choose from at 3 different

volume levels. One button sets both the tone and volume setting.

See the table opposite to help you select the right setting.

•

Press the SECRECY (Program) button. The LED will start to flash.

•Press the

(Ringer) button.

•Press the keypad button, 0 to 9, for the tone/volume you want.

The display will show the current setting and you will hear a

beep from the handset which is not audible unless held up to

the ear, e.g. Press 5 = Tone 2 at medium volume (see table).

Display shows RINGER TONE VOLUME

•Press the SECRECY

(Program)

button. The LED will stop

flashing. Your selected setting is now stored.

To adjust the speaker volume

The speaker volume can only be adjusted when the telephone is

off the base.

The switch can be found on the left hand side of the telephone.

There are 5 levels. 1 = quietest. 5 = loudest.

The volume will remain at the level you have set between calls

until you adjust it again.

Press to increase the volume.

Press to decrease the volume.

The display will show the volume increase or decrease.

Vol.1 Vol. 2 Vol. 3

Tone Quiet Medium Loud

Tone 1 123

Tone 2 456

Tone 3 789

No Tone 0 = Silent

(the display will show Ringer Off to confirm setting)

Duet 600 – Edition 4.2 – 13.9.00

Setting Up

Please read the instructions carefully before use, and keep this

user guide for future reference.

Connect the telephone line cord

Call Timer

Your Duet 600 automatically times the duration of all outgoing

and incoming calls. The call timer is shown on the right of the

display, replacing any number that was there, e.g.

00-14

TIMER.

To redial the last number

•The last number dialled is stored in the redial memory.

•Press the REDIAL button. The number is shown on the display

and dialled automatically.

Using your Duet 600

telephone

To make a call

•Lift the handset. You will hear a dial tone.

•Enter the telephone number. The number will be shown on the

display and dialled.

To end a call

•Replace the handset.

To switch secrecy on and off

When on a call you can talk to someone in the same room,

without your caller hearing.

•During a call press the SECRECY (Program) button.

The LED will flash to indicate that secrecy is on. You can talk

and your caller will not hear you.

•To resume your call press the SECRECY (Program) button

again. The LED will stop flashing.

Safety information

Do not expose to direct sunlight.

Do not stand your product on carpets or other surfaces which

generate fibres, or place it in locations preventing free flow of air

over its surfaces.

Do not submerge any part of your product in water and do not

use it in damp or humid conditions, such as bathrooms.

Do not expose your product to fire, explosive or other hazardous

conditions.

Duet 600 – Edition 4.2 – 13.9.00

At a glance

When the ringer is switched off the ring indicator light will continue

to flash to indicate an incoming call. The ringer will remain

switched off until you lift the handset again. It is not possible to

switch the ringer off permanently.

If you are redialling a number when connected to a switchboard,

wait until you hear a dial tone, then press the 9 button, wait again

for a dial tone and then press REDIAL. This applies even if 9 is

stored in REDIAL.

down

To use the Recall button

You may need to use the RECALL button if you are connected

to a switchboard/PBX (Private Branch Exchange), contact your

PBX supplier for further information. The RECALL button is

also used for BT Select Services.

Storing and dialling numbers

You can store up to 10 numbers in the QUICKDIAL memory

(0 to 9) and a further 3 numbers using the MEMORY buttons

(M1, M2 and M3).

Your Duet 600 comes with memory labels which can be used

to keep a note of your stored numbers.

Redial

Recall

M3M2M1

Secrecy

Quickdial

Recall

Secrecy

Redial

Program

Pause

Ringer

Hook switch

Lets you make a

follow-on call without

replacing the handset.

Speaker volume

control buttons

Used to adjust the

speaker volume

of a call.

Quickdial button

Use to store and dial

Quickdial numbers.

Secrecy

(Program) button

Allows you to talk

to someone in the

same room without

your caller hearing.

LCD Display

Shows stored/

dialled telephone

numbers. Also

displays call timer

and other visible

information

Memory buttons

Use to store and

dial one-touch

numbers.

Recall button

For use with

switchboards and

BT Select Services.

Redial button

Press to redial the

last number called

or to enter a pause

in the memory.

To store a number using the MEMORY buttons

(M1, M2, M3)

•Press the SECRECY (Program) button. The LED will start

to flash.

•Press the MEMORY button (M1, M2, or M3) under which you

want to store the number. The display will show the location

you have chosen, e.g.

MEMORY

•Use the keypad to enter the telephone number.

•You can use the UP/DOWN button on the side of the telephone

to go back and delete if you have entered the wrong number.

•Press the SECRECY

(Program)

button. The number will stop

flashing and is now stored.

The display will show

MEMORY

1 Stored.

M3M2M1

Secrecy

To store a pause in the dialling sequence of a memory number,

e.g 9, pause, 6, press the REDIAL button.

1 2

Résumé du contenu

Page 1 - At a glance

Duet 600 – Edition 4.2 – 13.9.00To adjust the ringer tone and volumeThe Duet 600 has 3 ringer tones to choose from at 3 differentvolume levels. One bu

Page 2 - User Guide

Duet 600 – Edition 4.2 – 13.9.00Duet 600 – Edition 4.2 – 13.9.00Duet 600 – Edition 4.2 – 13.9.00To dial a number stored using the MEMORY buttons(M1, M