Binatone TERRAIN 650 Guide de l'utilisateur télécharger pdf

4.6 Setting the DW (Dual Watch)

In normal mode, press the MENU button 7 times, until the

(Dual Watch) icon and the Channel number blink on the

Press the (UP) or (DOWN) button to select the

DW (dual watch) channel (1~8, except the main channel).

Press the button to cancel DW mode and return

to the normal mode.

This unit is capable of monitoring two channels (main channel,

and the DW channel) in the standby mode. However, the unit

can only transmit a call using the main channel. The DW

channel can only monitor/receive a call transmitted by other

users with the same channel setting as the

To activate the Dual watch mode;

In the Dual Watch mode, the LCD screen will alternately

CALL button

- Press to send

ringing tone to other

PMR units

(UP)/ (DOWN)

buttons - Press to

change channel setting.

PTT (PUSH to TALK)

button - Press and

hold to transmit.

LATITUDE 650

USER GUIDE

Private obile Radio (

P R

1. LCD Screen

Channel Number. Changes from 1 to 8

as selected by the user.

CTCSS Code. Changes from 1 to 38

as selected by the user.

Displays when transmitting a signal.

Displays the current Battery charge

level.

Displays when receiving a signal.

Ear/Mic jack

M (Monitor)

button - Press and

LCD Screen

-Displays the current

channel selection and

other radio symbols.

(Power)/Menu button

- Press and hold to

turn the PMR unit

ON or OFF

Mic (Microphone)

Speaker

s during Channel scan mode.

Displays when the Key Lock feature is activated.

Displays when the Vox feature is enabled.

Displays when Key tone is turned ON.

Displays when the Stopwatch feature is turned ON.

Antenna

Key Lock

/Lamp

Car/Adaptor

Displays when the Dual Watch function is turned ON.

2. Installation

2.1 Removing the Belt Clip

a. Pull the Belt Clip Latch away

from the PMR.

b. While pulling the Belt Clip

Latch, push the Belt Clip up

as shown in Figure 1.

Figure 1

Figure 2

Belt clip

latch

2.2 Installing the Belt Clip

a. Slide the Belt Clip into the

slot as shown in Figure 2.

b. A “click” indicates the Belt

Clip is locked into position.

a. the Batte ry

Compartment Cover latch located near the bottom of the PMR,

then lift the Battery Compartment Cover.

b. Install the 3.7V, 650 mAh Li-Ion

rechargeable battery pack only.

c. Replace the Battery Compartment Cover, ensuring the botton

d. Replace the Blelt Clip, if required.

2.4 Charging the Rechargeable Battery pack

Using the AC-DC Adaptor (Dual type) plug

a. Insert the small plug on the end of the AC-DC adaptor into the

Charge jack located on the bottom of the unit (Figure 6).

b. Plug the AC adaptor into the 230V AC wall outlet.

Using the Car Adaptor charger plug (optional)

a. Insert the small plug on the end of the Car adaptor charger plug

into the Charge jack located on at the bottom of the unit (Fig. 7).

b. Plug the Car adaptor into the car cigarette socket.

Important: Turn

OFF the

PMR unit during intial

Charge the Battery pack

10~14 hrs. prior to initial

use.

Figure 6 Figure 7

When charging, the Battery level indicator icon will start scrolling on

the LCD Screen. It takes about 10 hours to fully recharge the battery

if become completely run down. A new battery takes up to 14

hours to fully charge.

3. Operation

3.1 Turning the Unit ON/OFF

3.2 Adjusting the Speaker volume

There are 8 volume levels.

To adjust the speaker volume level, press the (VOL)

button to increase, or press the (VOL) button to

decrease. During the adjustment, the LCD Screen will

display and the corresponding volume

level setting.

3.3 Receiving a Call

The unit is continuously in the Receive mode when the

unit is turned ON and not transmitting. When a signal is

received on the current channel, the receiving icon

3.4 Transmitting (sending)

Press and hold the PTT (Push to Talk) button to transmit

your voice. The transmit icon will display on the LCD

Hold the unit in a vertical position with the Mic

(Microphone) 5 cm away from the mouth. While holding

the PTT button, speak into the mic (microphone) in a

normal tone of voice.

Release the PTT button when you have finished

transmitting.

To Turn ON;

a. Press and hold the (Power) button. A special “beep"

sound will be heard and the LCD Screen will display the

current channel.

To switch OFF;

b. Press and hold the (Power) button. Two "beeps"

will be heard and the LCD Screen will

4.1 Changing Channels

The PMR has 8 available channels. To change channels, in

normal mode;

4. Functions and Settings

Charging the Rechargeable Battery pack continue ...

4.1.1 Monitor Function

4.2 Changing the CTCSS sub-channel

Press the button c ,

the CTCSS number will

start blinking on the LCD Screen.

While the CTCSS number is blinking, press the

(UP) or (DOWN) button to select one of the 38 CTCSS

sub-channels. (Set this option to “00” to allow the user to

transmit and receive a call using the main channels only.)

Press the button to confirm your selection and

return to the normal mode.

You can use the Monitor feature to check for weak signals

on the current channel.

a. Press and hold the button for 1 second to hear

the current channel or press and hold

Press the button again to turn off the Monitor

operation.

Each of the 1-8 channels has 38 sub channels (CTCSS code),

letting you set up group of users within the same channel.

To change the CTCSS sub-channel;

Changing Channels continue ...

Note:

Refer to the "Specifications" section of this user guider for

LOCK

Note:

When the Dual Watch function is activated, the VOX function will

be temporarily disabled until the Dual Watch mode is turned OFF.

Caution: D of used batteries safely, never burn them or put

type a

nd make that came with the unit.

Remove the

battery pac k if the unit will not be used for a long

period

of time.

To reduce the risk of electric shock, do not expose this appliance to

rain an

d moisture.

Important:

Check the channel activity by pressing and holding the M (Monitor)

button. You will hear static if the channel is unoccupied. Do not

transmit if someone is talking on the current channel.

In order for other people to receive your transmission, they must

also be on the same Channel and CTCSS code (if applicable) that

you are currently using. Refer to the "Changing Channel" section

for more information.

LOCK

Channel

- Press to program

the PMR settings.

Button

- Press and hold to

Press to turn on the

LCD backlight for

V (Volume) button

Press to adjust the

speaker volume level

Charge jack

on e

a. Press the

desired channel.

he channel changes from 1 to 8,

(UP) or (DOWN) button to select the

or from 8 to 1.

turn blank.

4.3 TX Power H (High)/LO(Low) feature

This feature allows you to set the transmitting power

level to high or low efore transmitting speech to other

Press the button twice, until the

If High is selected, the PMR will transmit at maximum power

and a longer transmission range.

PMR unit .

(The Default is High Power output)

icon blinks,

(UP) or (DOWN) button to select

the

the desired power

output.

Press the button to confirm your selection and

return to the normal mode.

L K

Press the MENU button 3 times, until the (Vox) icon

blinks on the LCD Screen.

Press the (UP) or (DOWN) button to select the

VOX (1, 2, 3, 4 or 5) sensitivity. (5 is most sensitive, 1 is

In VOX mode, the PMR will transmit a signal only when it is

activated by your voice or other sounds around you. The unit

will transmit for a further for 1 second even if you stop talking.

To set the VOX sensitivity level;

Press the button to confirm your selection and

return to the normal mode.

4.4 Setting the VOX (Voice Activated) Sensitivity

LOCK

ress the (UP) or (DOWN) button to select ON/OFF .

Press the button to confirm.

displays on the LCD

Screen .

When your PMR is first turned , the VOX function will be

disabled.

Note:

Press the MENU button 5 times, until the (SCAN) icon,

the LCD Screen.

Channel scan performs searches for active signals in an

endless loop from channels 1 to 8. To turn ON;

4.5 Setting the Channel Scan

Setting the Channel Scan continue ...

Press the (UP) or (DOWN) button to activate the

channel scan mode.

The channel number on the LCD Screen changes rapidly

until an active signal is detected.

When an active signal (one of the 8 channels) is detected,

channel scan pauses on the active channel.

Press the button to communicate with the active

signal channel, and the channel scan will be deactivated.

(Lock)

(To deactivate the

channel scan mode, press the button. The LCD

Screen will immediately return to the normal mode with

the previous channel setting.)

(Lock)

Press the (UP) or (DOWN) button to activate the 1-38

sub channels scan mode. (CTCSS code)

Press the button to select CTCSS code scan. The

4.7.1 Sending a Call-Ring tone

With the PMR in normal mode, press the button.

The microphone will be muted and the unit will

transmit the current Call-Ring tone to other user/s

set to the same Channel and CTCSS code.

everything on

Note:

When the Channel Scan is activated, the VOX function will be

temporarily disabled until the Channel Scan function is turned OFF.

Press the MENU button 8 times, unit (Call-Ring tone

icon) displayed on the LCD Screen and the current

Call-Ring tone number blink .

While the Call-Ring tone number is blinking, press the

Call-Ring tone sound will be played when changing from

one tone to another.

Press the button to confirm your selection and

return to the normal mode.

You can use the Call-Ring tones to alert the other user/s or to

identify yourself. The PMR is equipped with 5 different types

of Call-Ring tones. To change the Call-Ring tone setting, in

normal mode;

LOCK

4.7 Changing the Call-Ring tone

CALL

Displays when Roger tone is turned ON.

10 seconds.

lock and unlock

it's

Only replace the Rechargeable battery pack with one of the same

them where they could get punctured.

details of the requencies usedf

Transmit ( )

, b

press

give

the

the button for 5 seconds to continuously monitor

(

hold to monitor the

current channel.

- Press to confirm menu

selections.

When the transmitting power is set to low.

Display

Displays when setting the speaker volume

Flashes when in power save mode.

Remove the Blet Clip, and slide down

edge clicks firmly into position.

charging.

ispose

will be displayed on the LCD Screen.

Screen.

the

current channel

mode and

, with the numbers to right flashing

least sensitive).

and Channel number, flash on

SC icon and the CTCSS numbers will flash.

DW channel.

LCD Screen.

display the Main and the DW channel numbers.

(UP) or (DOWN) button to change the setting. The

1 2

Résumé du contenu

Page 1 - Private obile Radio (

4.6 Setting the DW (Dual Watch) In normal mode, press the MENU button 7 times, until the (Dual Watch) icon and the Channel number blink on

Page 2 - Declaration of Conformity

SymptomSolutionNo power.The may be .batteriesCheck the battery pack is installed properly.Receptionis weak.Press the vol (UP) button to increas

Plus de documents pour Les radios bidirectionnelles Binatone TERRAIN 650

Voir le document Binatone TERRAIN 650 Guide de l'utilisateur

Binatone TERRAIN 650 Guide de l'utilisateur (11 pages)

Commentaires sur ces manuels

Pas de commentaire

Binatone TERRAIN 650 Guide de l'utilisateur

Naviguer en ligne ou télécharger Guide de l'utilisateur pour Les radios bidirectionnelles Binatone TERRAIN 650. Binatone TERRAIN 650 User guide Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Les radios bidirectionnelles Binatone TERRAIN 650

Commentaires sur ces manuels

Produits connexes et manuels pour Les radios bidirectionnelles Binatone TERRAIN 650